Jump to content

vicki

Registered Users - Approved
  • Posts

    11
  • Joined

Converted

  • FusionPro Products
    No

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

vicki's Achievements

Rookie

Rookie (2/14)

  • First Post Rare
  • Collaborator Rare
  • Conversation Starter Rare
  • Week One Done
  • One Month Later

Recent Badges

10

Reputation

  1. I've uploaded the files. Thanks. FP Stack Sheet Count Test.zip
  2. Helped to hit "upload".FP Stack Sheet Count Test.zip
  3. When using stacks and sheet counts I'm having a problem getting the correct total sheet count after the 2nd stack. I've attached the small test files I've been using – 2up, stacks of 10. If I run 20 records it comes out fine. Slugline reads F. 1 of 10, F. 2 of 10, etc. If I run 17 records it comes out fine .... F. 1 of 9, 2 of 9, etc. BUT if I run 26 records I get ... 1 of 15, 2 of 15, 3 of 15, like it's a full stack when it isn't. It should read 1 of 13, 2 of 13, etc. FP Stack Sheet Count Test.zip
  4. I apologize for the thread issue. Thanks so much for your reply. Because of restrictions on this job I'm limited as to what I can send. Luckily it's a font issue and I'm hoping one paragraph will help. I've attached a file that will include that sample and required documents, the fonts I used as well as just a sample of all the Khmer fonts I found along the way. The font I used, KhmerOSContent, was the only one I found to show correctly in the Text Editor window. I had been through so many and thought I found the one. It was hard to accept it wouldn't preview and print the same. I have two languages left after Khmer, Arabic and Farsi, right to left. I have a solution I can use if necessary but it's definitely a last resort. Can this be done as text, using fonts? If so ..... how? Should I start a new thread with that question? Thank you. Vicki Khmer sample.zip
  5. What about Khmer? I have a project using Arabic, Chinese, Farsi, Hmong, Khmer, Korean, Russian, Tagalong, Vietnamese & Western Armenian. I'm currently working on Khmer and having problems. Characters are correct when viewed in the FP Text Editor but not when I go to Preview and/or print. I've attached 2 screenshots showing the problems. The first character is missing and towards the end of the line there's a backwards looking S with an accent below it. When previewed and printed that accent turns into a +. Vicki S. O'Neil Printing
  6. This was just what I needed but I can't seem to find solution to one issue. I have a file where the last record overflows to 9 pages. Everything is fine until until it's imposed. During imposition I get an error and instead of adding 3 pages it truncates the 9th page. Error: The number of pages in this record does not match the imposition signature: 2 pages will be truncated. I've tried changing imposition every which way and have attached screenshot of it. It's an unusual one because of the nature of the job. How can I get around this? I'm using the coding exactly as shown here.
  7. Fixed it by exporting Format & Data Definition files to folder containing FusionPro PDF. There may be an easier way but since switching to FP Server this is the only way I could get PPML files to work on the Command Workstation.
  8. We are also getting this error. I had no problem until I had to start using FusionPro Server. Help!
  9. I have 10,000 – 10 page coupon books. Each page in a book is a single, numbered coupon, all 10 coupons in the book have the same number. It's running 4up with a slip sheet from different drawer after each set of 10. I've got it all working except for the order. I don't want 1, 2, 3 & 4 on 1st sheet and so on. How do I get it to number as a stack? Using OnRecordStart, repeatRecordCount for 10 sheets. Have unused page set-up for slip sheet. Thanks, Vicki
×
×
  • Create New...